Why Invest in Automated SEO Workflows?
A benefit to this setup is that it takes only seconds to shift from lathe to milling operations.
This would make a beneficial 2nd job although there is more filing, sanding, and polishing than turning.
Slitting is sluggish work with this setup however it does the task, witness the collet revealed. This collet was not drilled precisely so it is ineffective due to extreme runout.

The cross feed and substance dials were transformed to free spinning with friction lock simple to do, works well, replaces the friction spring under the dial. My original factor for getting a lathe was to make products associated with my microscopic lense pastime but I entered into adjusting lathe associated things.
A second Lucite project was an optical center punch patterned after one discovered on Harlan's website(Disappeared 3/13). A combination carriage stop/ dial holder was adapted from EngineMan's design; I copy only the very best! A clamp knurler was built from Martin Cleeve's style. His article recommends using the cross feed to knurl however this puts significant strain on the cross feed lead screw and nut; utilizing the carriage feed instead works well and puts less stress on the maker.

Maximizing Scalable ROI Through Technical Link Automation
Nothing is lost here at Hardship Acres-- a roller from that Nordic Trac was adapted to prevent the discharge chute on my lawn mower from digging in on high angle changes. I made a number of MT2 tapers to hold frequently used drill bits: the scrooge's option to a tailstock turret. When is a tool height gauge not a tool height gauge? When it's a die holder-- you get two for the rate of one with this approach.
I copied Varmint Al's concept for a tailstock flag and meter. Used a piece of 1/2" Lucite for the flag, the magnet is the rotor from a VCR takeup motor with an aluminum bracket to install the meter; simple, cheap, reliable. The DRO has further streamlined drilling to depth. Made a plinth to change the compound for most things aside from threading and tapers.
Ultimately I figured out that retracting the substance so the tool point is over the cross slide (not cantilevered out to the headstock side) assists reduce chatter and the plinth I made doesn't permit this. A Homier mill has actually been added to my shop. This doesn't fit perfectly within the title of my website so I don't understand exactly how I'll work that out however after wrestling this 700 pound guy down the stairs and onto the table, the mill remains! One required adjustment with a mill is tramming.
Expert Advisory for High-Volume SEO Workflows
A Mini-Tinker cutter mill didn't work as I hoped for honing end mills so eventually I bought a cutter grinder (see listed below) which didn't exercise either ... Tool holders to fit my Phase II toolpost were on my to-do list for a while; the new mill made many things possible.
I get a much better surface on steel with this toolholder than with regular toolholders and bits so I now utilize this for most turning and facing. This didn't work as well as I hoped so I split the old nut lengthwise instead but it broke when squeezed so I use it with 5 thou backlash.
; this is more capable than either of my earlier techniques to end mill sharpening. This is much more useful than expected, well worth doing.
In making the leadscrew for the Brooks-Stent I required a sharp threading bit so I constructed the honing jig from "Screwcutting in the Lathe" by Martin Cleeve. This jig makes the task fast and easy. A little try out this jig showed that it can be utilized to sharpen many lathe (and shaper) bits besides threading bits and the results are plainly better than my hand sharpening attempts.

I constructed a Geo. I do a fair quantity of threading so I've developed a regular for it which this tool streamlines.
Maximizing Scalable ROI Through Professional SEO Automation
Integrated with the retracting toolholder this speeds up threading considerably. Built a graver rest for the minilathe; a collet chuck or comparable is needed to use it securely. Added a dog clutch type carriage auto-stop to more improve threading; this supplies automated thread pickup on both imperial and metric threads plus it gets rid of need for the thread chasing dial.
As a non-woodworker, the case is an on-going struggle although the momentary case is sufficient for now.
restore a project in GSA SERER-32 Collets can now be used on the 7x12, Rockwell 10" and the mill-drill.
Appears to work well, much easier on the machine than the pressure knurler however seems a little fussier to set up.
Achieving Technical Mastery in Link Project Building
a digressive ball cutter. Developed a Tap Chuck primarily to see how the mechanism worked in practice (seems to work well). Made a Lantern Chuck and a Screw Slotter, both of which are most likely of interest mainly to clockmakers. Made a knife sharpener to make our cooking area knives work much better.