Comparing Traditional and Automated Link Workflows
An advantage to this setup is that it takes just seconds to move from lathe to milling operations. The drawback to the brand-new toolpost (and there's always a downside) is that it limits the size of items which can be turned due to its large size; I added the customized compound rest # 1777 from LMS to assist accommodate this and eventually modified the cross slide to permit more range.
This would make a useful second project although there is more filing, sanding, and polishing than turning.
The equipment is the chuck extractor, the "?" gizmo is a wrench to use more torque to the gear. The chuck is revealed here in the lathe. The collets are another part of this job; this is a picture of the raw product, a bought collet, and a partly finished set. To slot the collets I purchased a slitting saw, then made an arbor to fit the collet chuck - here is a photo of the parts. Slitting is sluggish deal with this setup but it gets the job done, witness the collet revealed. This collet was not drilled accurately so it is ineffective due to excessive runout. Ball bearings were contributed to the mini-lathe controls, starting with the cross slide followed by the compound (a lot easier to do than the cross slide).

The cross feed and compound dials were transformed to totally free spinning with friction lock simple to do, works well, changes the friction spring under the dial. My original reason for getting a lathe was to make items associated with my microscopic lense pastime however I got into adjusting lathe associated things.
A second Lucite project was an optical center punch patterned after one discovered on Harlan's website(Disappeared 3/13). A combination carriage stop/ dial holder was adapted from EngineMan's style; I copy only the very best! A clamp knurler was constructed from Martin Cleeve's style. His short article recommends using the cross feed to knurl however this puts considerable stress on the cross feed lead screw and nut; utilizing the carriage feed rather works well and puts less strain on the machine.
Achieving Professional Mastery in SEO Automation
When is a tool height gauge not a tool height gauge?-- you get 2 for the cost of one with this technique.
Utilized a piece of 1/2" Lucite for the flag, the magnet is the rotor from a VCR takeup motor with an aluminum bracket to mount the meter; basic, cheap, efficient.
Ultimately I determined that retracting the substance so the tool point is over the cross slide (not cantilevered out to the headstock side) helps reduce chatter and the plinth I made doesn't permit this. A Homier mill has actually been added to my shop. This doesn't fit well within the title of my site so I don't know exactly how I'll work that out but after battling this 700 pound guy down the stairs and onto the table, the mill stays! One necessary adjustment with a mill is tramming.
Comparing Traditional and Automated SEO Workflows
A Mini-Tinker cutter grinder didn't work as I hoped for sharpening end mills so ultimately I acquired a cutter grinder (see listed below) which didn't work out either ... Tool holders to fit my Phase II toolpost were on my order of business for a while; the new mill made numerous things possible.
I get a better surface on steel with this toolholder than with routine toolholders and bits so I now utilize this for most turning and dealing with. I made Will Hamlyn's split nut mod to decrease backlash in the cross slide. This didn't work as well as I hoped so I divided the old nut lengthwise instead however it broke when squeezed so I utilize it with 5 thou backlash.
; this is more capable than either of my earlier techniques to end mill sharpening. This is much more useful than anticipated, well worth doing.
In making the leadscrew for the Brooks-Stent I needed a sharp threading bit so I constructed the sharpening jig from "Screwcutting in the Lathe" by Martin Cleeve. This jig makes the job quickly and easy. A little explore this jig showed that it can be used to hone many lathe (and shaper) bits other than threading bits and the results are plainly much better than my hand honing efforts.

I developed a Geo. I do a fair quantity of threading so I have actually established a routine for it which this tool streamlines.
Achieving Technical Efficiency in Link Automation
Combined with the retracting toolholder this speeds up threading significantly.
As a non-woodworker, the case is an on-going struggle although the short-term case is adequate for now.
what's included in a GSA SER projectMade a tapping guide from a surplus sign stand. Ended up an ER-32 collet chuck for the Rockwell. ER-32 Collets can now be utilized on the 7x12, Rockwell 10" and the mill-drill. Little tools get magnetized accidentally (magically) in my shop so I made a demagnetizer from scrap plus small neodynium magnets.
what's included in a GSA SER projectSeems to work well, simpler on the machine than the pressure knurler however appears a little fussier to set up.
Essential Tips for Managing Automated Backlink Operations
, both of which are likely of interest mainly to clockmakers.