Securing Global SEO for 2026 Standards
A benefit to this setup is that it takes only seconds to shift from lathe to milling operations. The downside to the new toolpost (and there's always a disadvantage) is that it limits the size of items which can be turned due to its sheer size; I added the customized compound rest # 1777 from LMS to help accommodate this and eventually customized the cross slide to permit more range.
This would make a useful second project although there is more filing, sanding, and polishing than turning.
Slitting is slow work with this setup but it does the job, witness the collet revealed. This collet was not drilled properly so it is useless due to excessive runout.

The cross feed and substance dials were transformed to free spinning with friction lock simple to do, works well, changes the friction spring under the dial. My original factor for getting a lathe was to make products associated with my microscope hobby however I got into adjusting lathe associated things.
A second Lucite job was an optical center punch patterned after one discovered on Harlan's site(Vanished 3/13). A combination carriage stop/ dial holder was adapted from EngineMan's design; I copy just the very best! A clamp knurler was constructed from Martin Cleeve's design. His post recommends utilizing the cross feed to knurl but this puts substantial pressure on the cross feed lead screw and nut; using the carriage feed rather works well and puts less pressure on the maker.

Building Sustainable SEO Systems for 2026
When is a tool height gauge not a tool height gauge?-- you get two for the cost of one with this technique.
I copied Varmint Al's idea for a tailstock flag and meter. Used a piece of 1/2" Lucite for the flag, the magnet is the rotor from a VCR takeup motor with an aluminum bracket to install the meter; simple, inexpensive, efficient. The DRO has actually further streamlined drilling to depth. Made a plinth to replace the compound for a lot of things other than threading and tapers.
Eventually I determined that pulling back the substance so the tool point is over the cross slide (not cantilevered out to the headstock side) helps in reducing chatter and the plinth I made doesn't allow this. A Homier mill has been contributed to my store. This does not fit well within the title of my website so I do not understand exactly how I'll work that out however after wrestling this 700 pound guy down the stairs and onto the table, the mill stays! One needed change with a mill is tramming.
How to Master Advanced Backlink Workflows
A Mini-Tinker cutter grinder didn't work as I wished for honing end mills so ultimately I acquired a cutter grinder (see below) which didn't exercise either ... Tool holders to fit my Stage II toolpost were on my to-do list for a while; the new mill made lots of things possible.
I get a much better surface on steel with this toolholder than with routine toolholders and bits so I now utilize this for most turning and facing. This didn't work as well as I hoped so I divided the old nut lengthwise instead but it cracked when squeezed so I use it with 5 thou backlash.
Ultimately I constructed a Brooks-Stent cutter mill; this is more capable than either of my earlier approaches to end mill honing. I modified the depth stop on my HF drill press (idle hands do the devil's work). This is much more beneficial than anticipated, well worth doing. Added DROs to the lathe using 6" scales.
In making the leadscrew for the Brooks-Stent I required a sharp threading bit so I developed the honing jig from "Screwcutting in the Lathe" by Martin Cleeve. This jig makes the task quick and easy. A little explore this jig revealed that it can be utilized to hone many lathe (and shaper) bits other than threading bits and the outcomes are plainly better than my hand honing efforts.

I constructed a Geo. I do a reasonable amount of threading so I've established a regular for it which this tool simplifies.
The Key Advantages of Technical SEO Automation
Combined with the retracting toolholder this speeds up threading significantly.
An ER-32 collet chuck with travel through was required to streamline another project. Built a sensitive drill holder; it takes more force than anticipated to drill with tiny drills using this. A gearless clock has taken shape in my store and appears like it will continue ticking. As a non-woodworker, the case is an on-going battle although the temporary case is sufficient in the meantime.
GSA SER project in three stepsER-32 Collets can now be used on the 7x12, Rockwell 10" and the mill-drill.
GSA SER project in three stepsBuilt a cut knurler as an experiment. Appears to work well, much easier on the machine than the pressure knurler but seems a little fussier to set up. Added info on making counterbores from drill rod. Copied Dan Gelbart's Laser Center Finder idea for use with the mill or drill press.
Essential Tips for Managing Professional Backlink Systems
, both of which are likely of interest primarily to clockmakers.